- 您现在的位置：买卖IC网 > Sheet目录323 > DV164131 (Microchip Technology)KIT STARTER PICKIT 3
PICkit? 3 User’s Guide
9.5
SETTINGS DIALOG
Select either Debugger>Settings or Programmer>Settings to open the Settings dialog
and set up the PICkit 3 programmer/debugger.
Note:
Tabs displayed will depend on the selected device.
?
?
?
?
?
?
?
?
?
Settings Dialog, Program Memory Tab
Settings Dialog, Configuration Tab
Settings Dialog, Freeze on Halt Tab
Settings Dialog, Status Tab
Settings Dialog, Clock Tab
Settings Dialog, Secure Segment Tab
Settings Dialog, Warnings Tab
Settings Dialog, Power Tab
Settings Dialog, Limitations Tab
9.5.1
Settings Dialog, Program Memory Tab
This tab allows you to set up debug/programming options.
TABLE 9-6:
PROGRAM MEMORY OPTIONS
Allow PICkit 3 to select
memories and ranges
Manually select memories
and ranges
If selected, the PICkit? 3 uses your selected device and
default settings to determine what to program.
If selected, you must determine the Memories, Program
Memory Range, and Program Options for the selected
device.
Memories:
Program
Configuration
EEPROM
ID
Boot Flash
Program Memory Range:
Start, End
Check to program Program Memory into target.
Check to program Configuration bits into target.
Note: This memory is always programmed when
debugger selected as a debugger.
Check to erase and then program EEPROM memory on
target, if available. Uncheck to erase EEPROM memory
on target.
Check to program ID Memory into target.
If supported, check to program boot memory on target
The starting and ending hex address range in program
memory for programming, reading, or verification.
If you receive a programming error due to an incorrect
end address, you need to perform a reconnect, correct
the end address and program again.
Note: The address range does not apply to the Erase
function. The Erase function will erase all data on the
device.
Program Options :
DS51795A-page 56
Erase all before Program
Preserve Program Memory
Range
Check to erase all memory before programming begins.
Unless programming new or already erased devices, it is
important to have this box checked. If not checked, the
device is not erased and program code will be merged
with the code already in the device.
Check to preserve memory range.
Start, End – The starting and ending hex address range in
program memory for preservation.
? 2009 Microchip Technology Inc.
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
DV164132
KIT EVAL F1 FOR PIC12F1/PIC16F1
DV243003
KIT STARTER FOR SRL MEM PRODUCTS
DVA1001
ADAPTER FOR PIC16F716 18DIP
DVA1004
DEVICE ADAPTER 8/14/20DIP
E3R-D12GP-P
RELAY RCVR PLUG-IN DIMMER
E3R-R12-3HOTP
RCVR 3WIRE RELAY 120V
E3R-R12GP
RCVR PLUG-IN RELAY
E3T-MICFP-40
CONVERTER 4-CH SLT SENSOR
相关代理商/技术参数
DV164131
制造商:Microchip Technology Inc 功能描述:PICKIT 3 DEBUG EXPRESS
DV164131-XLP
制造商:Microchip Technology Inc 功能描述:KIT DEV PICKIT 3-XLP/NANOWAT
DV164132
功能描述:开发板和工具包 - PIC / DSPIC F1 Evaluation Kit RoHS:否 制造商:Microchip Technology 产品:Starter Kits 工具用于评估:chipKIT 核心:Uno32 接口类型: 工作电源电压:
DV164132
制造商:Microchip Technology Inc 功能描述:PIC12F1xxx/PIC16F1xxx F1 Evaluation Kit
DV164133
功能描述:电源管理IC开发工具 Energy Harvesting Development Tool
RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V
DV164136
功能描述:开发板和工具包 - PIC / DSPIC PIC18F DEV Kit (with PICkit 3) RoHS:否 制造商:Microchip Technology 产品:Starter Kits 工具用于评估:chipKIT 核心:Uno32 接口类型: 工作电源电压:
DV164139
功能描述:开发板和工具包 - PIC / DSPIC Lo PIn Count USB Dev Kit (w/PICkit 3) RoHS:否 制造商:Microchip Technology 产品:Starter Kits 工具用于评估:chipKIT 核心:Uno32 接口类型: 工作电源电压:
DV17K3225T
制造商:SEI Stackpole Electronics Inc 功能描述:- Tape and Reel 制造商:SEI Stackpole Electronics Inc 功能描述:Var MOV 17VAC/22VDC 100A 27V 3225 SMD T/R